Deformed SRX ball: how to reshape it?
Practical guide - Juggling ball maintenance
SRX ball deformed or deflated: How can we restore its round shape?
Your SRX juggling ball appears to be deflated. has hollows or no longer retains Its round shape? A simple interview usually allows to restore its appearance and its usual consistency.
Discover how to remove the cap. clean the opening and put back Your ball in shape without any special tools.
Why is my SRX ball deforming?
The SRX balls, manufactured by Play Juggling, These are not classic inflatable balls. They have a thin and flexible shell. partially filled with fine quartz sand.
Their round shape depends in particular on the presence of air inside the hull. When this air gradually escapes, The ball may have hollows. dents or a deflated appearance.
This phenomenon can occur when very small grains of quartz come to fit between the cap and the edge of the opening.
These grains can prevent a closure perfectly airtight and allow air to escape.
A deformed SRX bullet is not necessarily damaged. In most cases, a simple cleaning the opening and a correct replacement of the cap are enough to restore its roundness.
Is the cap of the SRX ball glued on?
No, the cap is not glued on. It is designed to be removed and then put back in place.
Its slightly conical cylindrical shape and its positioning groove allow you to remain properly installed.
Therefore, it is not necessary to to cut, pierce, or use a tool to remove it.
In this guide
Before you begin: prepare the equipment
Maintaining an SRX ball does not require No special equipment required.
You will need:
- Your SRX ball needs maintenance.
- A clean, dry cotton swab.
- A plate or a bowl.
- A quiet and well-lit place.
Perform the entire procedure above a plate or bowl . This will prevent you from losing the cap and will be able to collect any grains quartz.
Always work with gestures. gentle and without sudden movements.
Tutorial: Maintaining an SRX ball step by step
Carefully remove the cap
The cork is held in a small hole from the case. To remove it, you will utilize the flexibility of this shell.
- Hold your ball with the cap facing upwards .
- Locate the cap under the shell by gently feeling the ball.
- Position your thumb on the case, approximately 4 cm from the cap , in order to feel one's inner self.
- Gently press through the case to gradually push the cork from the inside out .
- When the cork protrudes sufficiently, grasp it gently with your fingers and remove it completely.
Trick : The cap is not glued. If it seems to resist, don't look for it. to pull it off with a tool. The flexibility of the shell allows to push it gradually from the inside.
As soon as the cap is removed, Avoid putting any pressure on the shell. This could cause the exit quartz sand through the opening.
Clean the opening of the ball
Some grains of quartz can accumulate at the opening and prevent the cap from closing correctly the ball.
This cleaning process removes the small grains likely to create an air passage.
- Take a clean and perfectly dry cotton swab .
- Gently insert its end in the opening of the ball, at a maximum depth approximately 1 cm .
- Make a few small movements rotating to clean the edge inside the hole.
- Gently remove the cotton swab.
Do not use water or alcohol. nor cleaning products. A dry cotton swab is all you need.
There's no need to push it in deeply. Only the inner edge of the opening needs to be cleaned.
Replace the cap correctly
As soon as air enters the ball, she can find it immediately its round shape.
It is now important to replace the cap without compressing the ball , in order to keep the air inside.
- Hold the ball gently with the opening facing upwards.
- Present the cork in its opening, narrow part towards the inside.
- Gently press down on the cap towards the center of the ball, without crushing the hull.
- Continue until the plug naturally positions itself in its groove.
How to tell if the cap Is it well positioned?
Once installed, it practically at the level of the ball's surface. He may remain slightly in the background. approximately 0.5 mm.
Its positioning groove allows you to find naturally its place.
Avoid pressing on the entire of the ball during this stage. Excessive compression can to bring out the air and cause a new deformation.
Check that the ball has regained its shape
Once the cap is correctly replaced, your SRX ball must have a generally round and regular shape.
The indentations caused by the Air leaks should have disappeared. The ball also finds its usual consistency.
Is your SRX ball round again?
Congratulations! The interview is over.
You can resume your exercises juggling with your ball.
What if the ball remains deformed?
If she doesn't find it immediately its shape, it is possible that air either came out during closing.
In this case, start again gently. the procedure:
- Remove the cap again.
- Let the air in and the shell regain its roundness.
- Check that the opening is clean.
- Replace the cap without compress the ball.
If the problem persists, examine the edge of the opening in order to verify that it does not present no tears.
A tear in this area is extremely rare, but can compromise the seal.
Contact our team before any attempt at repair.
Do not glue the cap. This operation is not a recommended maintenance method. A possible exceptional repair must be assessed on a case-by-case basis.
How often should SRX balls be serviced?
We recommend conducting this interview preventive approximately every 3 to 6 months .
This frequency may vary depending on the intensity of ball use, their storage conditions and their general maintenance.
If your ball starts to show hollows or a loss of roundness before this deadline, you can perform the procedure earlier.
Don't wait for your ball either severely deformed to check that its cap is clean.
Regular maintenance helps to preserve its shape and duration of use.
Frequently Asked Questions about SRX ball maintenance
Can an SRX ball be reinflated?
SRX bullets do not inflate with a pump like a balloon. However, when the hull became deformed because of a air loss, it is usually it is possible to restore its shape by removing and then replacing correctly its cap.
Why is my SRX juggling ball Does it have any dips?
Small grains of quartz can slip between the cap and the opening of the ball. Air can then escape, resulting in deformation of the soft shell.
Is the cap of an SRX bullet glued on?
No, the cap is removable. It is maintained by its shape and by a positioning groove. It can be removed by pushing it gently from the inside out the outside, through the hull.
Should we use a tool? To remove the cap?
No. The flexibility of the hull allows to push the cork with the thumb. Do not use a sharp object or sharp.
Which product to use To clean the opening?
No product is needed. Simply use a cotton swab clean and dry, inserted on approximately 1 cm maximum, with slight rotational movements.
Why does the ball deform? After replacing the cap?
Excessive pressure during replacing the cap can release air. Remove the cap again. Allow the ball to regain its shape. then close it gently without compressing the shell.
When should you clean? The cap of an SRX bullet?
An interview about the opening It is recommended to do this every 3 to 6 months. It can be done earlier if the ball loses its round shape.
What to do if the bullet hole Is it torn?
This type of damage is very rare. Contact our customer service in order to evaluate possible solutions. Do not attempt to glue the cap without prior advice.
Need help with your SRX ball?
You have followed this tutorial, but your ball doesn't find Still not in shape?
Our NetJuggler team can help you to assist in identifying the origin of the problem.
Feel free to contact us attaching, if possible, a photo of your ball and its cap.
Comment / Question
!Be the First to comment!
